Release Notes for MOBOTIX MxDisplay Software

Document Information

Contents

The MOBOTIX MxDisplay is a video door intercom with touch screen, microphone, speaker, WiFi module, RFID module and integrated video management software for MOBOTIX door stations and cameras. These Release Notes contain a short technical description of the most important features of the software for the MOBOTIX MxDisplay.

Software Releases—Overview:

Notes:

• When installing the MxDisplay, make sure that the wire mesh of the network installation cable is properly connected to the ground contact as shown in the installation instructions. Failing to do so may result in a malfunctioning touch screen!
• In order to use the MxDisplay, the MOBOTIX door stations and other cameras need to run a software release 4.3.0 or higher.
• Please download the stable customer releases of the software from http://www.mobotix.com in the Support > Software Downloads section.
• Please send an email to intl-support@mobotix.com for feedback.

top

MxDisplay Software-Release V1.0.2.16

Creation Date: 2015-06-18

Publishing Date: 2015-06-26

Enhancements and Improvements

Redesigned "Access Control" Dialog, Tool Tips

The Settings > Access Control dialog has been completely redesigned. The menu structure, in particular, has been improved when adding new RFID cards. In addition, the dialog has been improved for adding PINs, users, parties and door stations that opens when tapping the "+" icon: When tapping and holding an icon, a text explains the icon's function. The same applies to all other dialogs that contain icons.

Note:
If a PIN has been set for an RFID card in the access control, the following applies when trying to gain access using the card: If a KeypadRFID controls the access, you also need to enter the assigned PIN, whereas a BellRFID will grant access using only the card.

New Functions for Softbuttons

Two new functions are available when defining "function icons":

• Announcement: Tap and hold an icon with this new function to make an announcement via the selected camera.
• Send message: This function allows sending a message via the MxMessageSystem of the selected camera. The camera can process the message itself or send it on to attached MxBus modules.

If function icons have been created, the tool bar beneath the live image shows an additional "checkerboard" icon. Tap on this icon to see and to use the defined function icons.

Note: To activate and define function icons, tap and hold the Home button in the MxDisplay main menu.

Enhanced Menus and Screens

• Screensaver: If at least one camera with an attached temperature sensor is connected to MxDisplay, the Standby mode (i.e., before switching of the display) automatically switches between time/date and temperature. You can modify this behavior in the Settings > MxDisplay Settings > Screensaver menu. In addition, the MxDisplay will not turn dark after a couple of minutes, but will follow the screensaver settings.

  Note: Changing the Black Screen and Activate after 1min factory default settings of the screensaver will increase the wear on the display, and thus reduce the life expectancy of the MxDisplay.

• Date and Time: The settings for a time server used by MxDisplay are now modified in the Settings > Installation > System Configuration > System Time menu. Note that you can set several connected time servers in that menu. MxDisplay will show the time in red in the main menu if no or only one time server has been defined. If you are using a camera with connected MX-GPS-Box or another time server with acceptable precision, MxDisplay shows the time in white. If the current time of a door station is in the future as compared to the MxDisplay, this will be recognized in door station events. MxDisplay will show an exclamation mark behind the event time and creates a permanent error message.

  Note:
  If neither an MX-GPS-Box nor another time server with acceptable precision can be used, MxDisplay can show the date and time in white anyway. To do so, activate the No Time Warning option in Settings > Installation > Display Configuration > Date & Time.

• Bell behavior: The behavior of individual bells and the reaction can be modified quicker in the Settings > Bell Behavior menu. In addition, you can modify existing mailboxes and record mailbox announcements.
• Adding cameras and changing network settings: When adding cameras in the Settings > Installation > Camera List > "+" icon, you can now set port numbers and activate/deactivate SSL for the cameras. This means that it is possible to use cameras e.g., via DynDNS in MxDisplay that use a special port for this purpose. When manually entering IP addresses for a camera, name server, gateway or the like, the numeric keypad pops up automatically.
• Event search: In the Event Search menu, you can use the "magnifying glass" icon to filter by cameras and event types.

Bugfixes

• Showing users and parties in Access Control
  When defining parties and users within parties, users were sometimes shown twice – once within and once outside of the parties.
• Custom weekly profiles in Access Control
  After defining and subsequent editing of custom weekly profiles, these profiles were sometimes shown twice. After deleting one of the profiles, both profiles disappeared. Also, changing the access mode to permanent access ("green key" icon) sometimes failed after using custom weekly profiles.
• Access control with custom time ranges
  Using custom time ranges for accessing with specific means (PIN, RFID card) could sometimes fail and did not produce the expected results.
• RFID cards sometimes "unknown"
  RFID cards that had been trained in several systems (e.g., Keypad and BellRFID) were sometimes rejected by MxDisplay with a "card unknown" message.
• Backup and restore of access control settings
  After backing up and restoring all settings of the Access Control dialog, the defined users and parties were missing.
• Ring tones not played fully
  On some ring tones, such as "DingDong", the beginning of the sound did not play and as a result, the sound was too short.
• "Last Event" function icon
  The "Last Event" function for function icons showed the event list and not the last event. The function has hence been renamed to "Event List".
• Cameras added with 169 IP address (Zeroconfig)
  When adding cameras, cameras that did not get an IP address from a DHCP server were sometimes added with an IP address in the 169 range (Zeroconfig) instead of their additional factory default IP address in the 10.x.x.x range.
• Reconnection after MxEasy Privacy Mode
  After activating the MxEasy Privacy Mode, a camera attached to MxDisplay cannot be shown any more due to the modified access data. This state continued even though the MxEasy Privacy Mode had been deactivated in the meantime. MxDisplay will now periodically try to reconnect to such a camera and automatically restores the access once the MxEasy Privacy Mode has been deactivated.

Known Limitations

• Red LED flashing
  Sometimes, the left LED will continue to flash red after loosing the connection to a door station/camera even though the connection has been re-established in the meantime.
• HTTP/HTTPS access using Bonjour
  Currently, the Bonjour service (used to make MOBOTIX devices know to other network devices) on an MxDisplay will advertise its HTTP port 80 and HTTPS port 443, regardless of the actual ports that have been assigned using the browser-based user interface of MxDisplay. Regardless of this, the unit uses the HTTP/HTTPS ports specified in the browser interface.
• Displaying/changing camera configuration settings
  Currently, the MxDisplay may not always show the current camera configuration settings, if these had been changed from another device or from the browser-based user interface of the camera. In such a case, you can reload the connections to all cameras and door stations (and thus, the configuration settings) by simultaneously holding the Letter, Home and Key buttons at the bottom until you hear five beeps.

top

MxDisplay Software-Release V1.0.2.0

Creation Date: 2014-11-14

Publishing Date: 2014-11-17

This is the first officially published software release for the MOBOTIX MxDisplay.

MxDisplay Features

"A Smartphone On the Wall"

That's the first impression of the new wall-mounted display from MOBOTIX. It can be integrated flush with the wall, comes in a stylish design in black or white and users can operate it using gestures, just like a modern smartphone. With just a few swipes, the user can look at an overview of the cameras in the house, retrieve the latest video messages of the door intercoms or create a new access transponder for a visitor.

The MxDisplay is extremely easy to operate and serves as an intercom for the video door station. Regardless of what menu the user is in, tapping the key icon immediately shows the live image of the door station. Tapping and holding opens the door. If necessary, you can increase the security by assigning a PIN or RFID transponder.

Main Features

Besides the features mentioned above, the MxDisplay has many more features; the most important ones are listed in the following:

• Intercom with live image
• Activate electric door opener and switch lights
• HD audio technology for high-quality voice connections between MxDisplay and camera
• Start an instant recording directly in the live image
• Play back mailbox and event recordings of door stations and cameras
• Integrated event search and player features
• Extensive RFID and access control features:
  • Train and manage RFID cards/transponders and access PINs
  • Create users and lock MxDisplay features for specific users
  • Scheduled access control for RFID cards and PIN codes
  • Combined access control of RFID card plus PIN
• Simple installation, optional wireless network connection
• WiFi functionality with different modes:
  • Client: MxDisplay is used as a WiFi client in an existing WiFi network
  • Extend Network (AP): MxDisplay is used as a WiFi access point for other devices (smartphones, tablets) in the same WiFi network for all devices
  • Separate Network (AP): MxDisplay is used as a WiFi access point in a separate WiFi network and also has a connection to the camera network (e.g., for different apartments without individual WiFi routers)
  • Camera Gateway (Client): MxDisplay is used as a WiFi client in a WiFi network that is different from the camera network (e.g., for different apartments with individual WiFi routers)
• Building automation features programmable (lights, shutters, etc.)
• Configuration of important camera settings
• Management of MxDisplay and system configurations
• Language support (DE, EN, FR, PT (Brazil), ES, IT)

Notes on Setting up MxDisplay

• IP address for DHCP and software update
  If the MxDisplay is connected to an existing DHCP server, you can see the current IP address by tapping on Home > Settings > About > Network Interfaces. You will need this IP address, if you want to update the software using the browser-based user interface of the device, for example. For updating the software, enter the IP address in a browser (user admin, password meinsm) and select Update system software (please also see the initial operation description in the MxDisplay Quick Install).
• Simultaneous Use of Ethernet and WiFi
  When simultaneously using the Ethernet and the WiFi network interfaces, you need to make sure that the IP address ranges of both networks are not overlapping. This would be the case, if both networks would use IP addresses in the range 192.168.0.x with a subnet mask of 255.255.255.0. To configure the Ethernet interface, open Settings > Installation > Display Configuration > Network. The WiFi interface is configured in Settings > Installation > Display Configuration > WiFi.
• Setting up RFID cards
  In order to use the RFID cards in a multi-door-station installation with the existing MxDisplay units, you need to initialize all door stations and MxDisplay units with the same RFID admin card.

Special Operating Instructions

• Push-to-Talk
  If you tap and hold the green receiver icon (two-way communication with the camera) longer than 10 seconds, it will lock and MxDisplay will continue to send the sound from its microphone to the camera. Press the green receiver icon again to stop sending audio to the camera and to hear the sound from the camera microphone on the MxDisplay. Press the red receiver icon to disconnect the audio connection to the camera.

Known Limitations

• HTTP/HTTPS access using Bonjour
  Currently, the Bonjour service (used to make MOBOTIX devices know to other network devices) on an MxDisplay will advertise its HTTP port 80 and HTTPS port 443, regardless of the actual ports that have been assigned using the browser-based user interface of MxDisplay. Regardless of this, the unit uses the HTTP/HTTPS ports specified in the browser interface.
• Display of dialogs after large "time lapses"
  If the MxDisplay is connected to a time server for synchronization purposes and the time needs to make a large correction (e.g., because the connection to the time server had been disrupted for a longer period of time), the MxDisplay may show incomplete or overlapping dialogs.
• Displaying/changing camera configuration settings
  Currently, the MxDisplay may not always show the current camera configuration settings, if these had been changed from another device or from the browser-based user interface of the camera. In such a case, you can reload the connections to all cameras and door stations (and thus, the configuration settings) by simultaneously holding the Letter, Home and Key buttons at the bottom until you hear five beeps.